Termite holes: what the small holes in your timber really mean
Found a hole in a skirting board? Stop before you poke it.
The commonest mistake with termite holes
Most people try to look inside. They push a screwdriver into the hole, scrape at it or blast it with a can of spray. Don't. Any of those moves can do more harm than the hole itself.
A hole in timber is a clue, not a diagnosis. It might be termites, a borer, or an old repair. Only an inspector can say which.
What termite holes look like
Termites rarely announce themselves with a neat round hole. They work inside the wood and keep the surface sealed to hold in moisture. When a hole does appear, it is usually ragged, small and surrounded by damaged paint or lining.
- Irregular or slit-shaped openings rather than clean circles.
- A blistered, bubbled or cracked patch of paint beside the hole.
- Soil-like or mud-like material packed inside or smeared around the edge.
- Timber that sounds hollow or papery when you tap near it.
- A thin mud tube running to the hole from a wall, pier or slab.
Mud tubes are the covered travel routes termites build. They are covered in mud tubes: what they are and what to do.
Termite holes versus borer holes
This is the comparison that trips people up. Borer holes are small, round and clean, like a pinprick. Fine powder called frass often spills out beside them. Termite openings are rougher and come with soil-like debris, not powder.
| Clue | Termites | Borers |
|---|---|---|
| Hole shape | Ragged, irregular, often slit-like | Small, round and clean |
| Debris | Soil-like or mud-like material | Fine, powdery frass |
| Inside the wood | Galleries along the grain, lined with soil | Tunnels packed with frass |
| Surface | Often blistered paint or papery skin | Often pinhole exits across the board |
The table is a guide, not a verdict. Some timber has both problems, and some holes are neither. Borers get their own treatment in the borers and rot section.
Why you should not plug, spray or probe the hole
Disturbed termites seal off that route and move somewhere else. The colony keeps feeding, now out of sight. That is the worst result, because the damage carries on where nobody is looking.
A supermarket spray does the same job and adds two more problems. It can destroy the transfer effect that professional non-repellent products and baits depend on. It also wipes out the evidence an inspector reads to work out where the activity comes from.
Filling the hole with putty is just as bad. It hides the clue and leaves the colony untouched.
Can you tell the species from the hole?
No. Different groups leave similar marks, and guessing the species from a photo or a description is unreliable. Getting it wrong can change the treatment. The inspector identifies the group, usually by looking at the soldiers under a lens.
What to do when you find one
- Stop. Do not probe, scrape, fill or spray.
- Take a photo with something for scale, such as a coin.
- Note the date, the room and anything nearby that looks unusual.
- Book a licensed timber pest inspector and ask for an inspection that follows the relevant Australian Standard.
- Let a licensed pest management technician handle any treatment.
What the visit involves is explained in what is a termite inspection. If the damage turns out to be real, the next step is in fixing termite damage: what happens first.
A single hole does not mean a small problem. Treat it as a reason to book an inspection this week, not next month.
Frequently asked questions
Do termites leave holes in wood?
Sometimes. They usually keep the surface sealed, so a visible hole is often ragged and comes with soil-like debris or blistered paint.
How do I tell termite holes from borer holes?
Borer holes are small, round and clean with fine powdery frass. Termite openings are rougher and come with soil-like material. An inspector should confirm which you have.
Should I fill or spray a hole I find in timber?
No. Filling or spraying hides the evidence and can push the colony to a hidden route. Leave it untouched and book a licensed inspector.
Sources
What this page explains is based on these official sources. If you check one and it does not match what you read here, send it to us and the article gets corrected.
- Queensland Building and Construction Commission. Protect against termites: termite management systems and inspections
- Department of Health, Victoria. Pest control: termites
- Standards Australia. Australian Standards (AS 4349.3 timber pest inspection, AS 3660 termite management)