Termite trails: what the lines and tubes on your walls mean
A fine line of mud on a wall is a road, and it leads somewhere.
A trail is a travel route, not a nest
A termite trail is the path workers use to move between the soil and the timber they are feeding on. In Australia the visible version is usually a mud tube: a pencil-width tunnel of soil built over brick, concrete or steel. It is covered because subterranean termites dry out and die in open air.
So a trail tells you where termites travel. It does not tell you where the colony lives, how big it is or how much damage is done. Those answers need an inspector.
The kinds of trail you might find
Not every line on a wall is a termite trail, and the differences are worth knowing before you phone anyone.
| What you see | Likely cause | What to do |
|---|---|---|
| Covered earthen tube up a pier, slab edge or wall | Subterranean termite travel route | Leave it intact and book an inspection |
| Thin muddy streak or smear on a surface | Termite workings, or splashed soil | Photograph it, do not wipe it, book an inspection |
| Fine dark trail across a surface | Often ants, not termites | Ask the inspector to check |
| Trail leading to a hole in timber | Possible entry point | Do not probe the hole |
Telling these apart from a photo is unreliable, even for professionals. That is one reason the visit matters.
Where termite trails turn up
Termites have to cross whatever they cannot eat, so trails collect at a short list of places.
- Subfloor piers and stumps, running up to the bearers.
- The slab edge, especially where a path or garden bed is built up against the wall.
- Weep holes in brickwork.
- Fence posts, retaining walls and timber in the yard.
- Plumbing and conduit entries where they pass through a slab.
Many trails are never seen at all, because they run inside the wall cavity. A visible one is often the lucky find.
Is the trail active or abandoned?
Everyone asks, and the honest answer is that you cannot reliably tell from the outside. A damp, dark, intact tube leans towards active. A dry, pale, broken one leans towards old. Both rules fail often enough to mislead.
A colony can be working in the building and not using that tube. A tube can look dead while termites feed behind it. If you decide a dry tube means the problem is over, you may talk yourself out of the one inspection that would have shown otherwise.
Do not break, brush off or spray the trail
Breaking a tube to look inside feels harmless. It is not. Termites treat a breach as a threat. The colony seals off that section and re-enters the building by a hidden route, so the damage carries on where nobody can see it.
Spraying the trail from the supermarket aisle does the same and adds two problems. It can wreck the transfer effect that professional non-repellent products and baits depend on. And it destroys the evidence an inspector reads to trace the activity back to its source.
Leave the whole tube as you found it. Photograph it from a few angles, with a coin beside it for scale.
What to do next
- Do not touch, break or spray the trail.
- Take photos and note the date and exact location.
- Book a licensed timber pest inspector and ask for an inspection to the relevant Australian Standard.
- Leave any treatment to a licensed pest management technician using APVMA-registered products.
The basics of what a trail is made of are in mud tubes: what they are and what to do. If you also see holes in timber, read termite holes. And the visit itself is described in what is a termite inspection.
A trail you can see means termites have already been through. Book the inspection this week.
Frequently asked questions
What do termite trails look like?
Usually a pencil-width tunnel of soil running up a pier, wall or slab edge. Sometimes just a thin muddy streak on a surface.
Should I knock down a termite trail?
No. Breaking it makes the colony seal that route and re-enter the building out of sight. Leave it intact and book a licensed inspector.
Can I tell if a termite trail is still active?
Not reliably. A damp, intact tube suggests activity and a dry, broken one suggests an old route, but both guides fail. An inspector can judge it.
Sources
What this page explains is based on these official sources. If you check one and it does not match what you read here, send it to us and the article gets corrected.
- Queensland Building and Construction Commission. Protect against termites: termite management systems and inspections
- Department of Health, Victoria. Pest control: termites
- Standards Australia. Australian Standards (AS 4349.3 timber pest inspection, AS 3660 termite management)