AS 3660.1: what it requires of a new building
The standard that decides how a new house is protected before anyone moves in, and the paperwork you should be handed at the end.
What AS 3660.1 actually covers
AS 3660.1 is the Australian Standard for termite management in new buildings. It sets out how a barrier or other management system is designed and installed as the house goes up, so the building is protected from day one.
It is not an inspection standard and it is not a treatment standard for an existing house. Inspections of finished homes are written to a different standard, AS 4349.3, and work on existing buildings follows AS 3660.2. Mixing them up is the commonest confusion in this area.
Why new buildings get their own standard
A new build is the one time a barrier can be fitted continuously and in the open. Slab edges, pipe penetrations and piers are all exposed before the floor goes down. After that, they are covered for good.
That is why the timing matters more than the product. A barrier with a gap in it is a barrier with a door in it. Termites find gaps because they are always searching, and the building cannot be checked properly once the finishes are on.
What the standard is built around
- A continuous barrier. Chemical, physical or a mix, with no breaks around the slab edge, service penetrations or piers.
- Visible inspection zones. Gaps that stay clear so an inspector can see a termite tube before it reaches timber.
- Records. A certificate when the work is done, and a durable notice fixed in the building.
- Maintenance. The system only keeps working if it is looked at on a schedule and the zones stay clear.
The paperwork you should receive
Ask for the certificate at handover. It should name the system, the date, the person who installed it and the product if a chemical was used. The durable notice is normally fixed somewhere permanent, often the meter box, so the next owner can read it.
If you cannot find either, say so before you accept the keys. A barrier you cannot prove was installed is a barrier you cannot rely on, and it can complicate things at resale.
| Question | What a good answer looks like |
|---|---|
| Which system was fitted? | Named on the certificate, with the date and installer |
| Who installed it? | A person you can check against your state licensing or building regulator |
| Where is the durable notice? | Fixed in a permanent place, such as the meter box |
| When is the first check due? | Written on the notice, with a recommended interval |
A barrier is not a guarantee
Even a perfect installation can be bridged. Soil piled against a wall, a garden bed over the slab edge or a timber stack against the cladding all give termites a way round. Later renovations that cut through the barrier break it, too.
So the standard gets you a good start, not a permanent shield. Regular inspections are what keep the protection real. See how often a house should be inspected.
If you find evidence in a new house
Do not break the tubes and do not spray anything. Disturbing a colony makes it abandon that route and re-enter somewhere hidden, and it destroys the evidence the inspector needs to find the entry point.
Photograph it from where you stand, then contact a licensed professional. Your certificate tells them what system is in place and where to look first. Who may inspect and who may treat is covered in licensed inspectors and technicians.
What this page cannot tell you
Requirements differ by state and by the building approval for your site, and a standard is only one part of it. Your builder, your building certifier or your state building regulator can confirm exactly what applied to your house. Interpreting a contract is a question for a professional, not for a guide.
Frequently asked questions
What is AS 3660.1?
It is the Australian Standard for termite management in new buildings. It covers how a barrier or management system is designed and installed while the house is being built, and what records are left behind. It is not a standard for inspecting finished houses.
Is AS 3660.1 the same as a pest inspection standard?
No. A timber pest inspection of an existing house is written to AS 4349.3, and work on existing buildings follows AS 3660.2. AS 3660.1 applies to new building work.
What paperwork should I get with a new house?
Ask for the termite management certificate and look for the durable notice fixed in the building, often in the meter box. Together they record the system, the installer, the date and the recommended inspection interval.
Does a barrier mean I never need an inspection?
No. A barrier can be bridged by soil, garden beds or stacked timber, and later building work can cut through it. Regular inspections by a licensed professional keep the protection working.
Sources
What this page explains is based on these official sources. If you check one and it does not match what you read here, send it to us and the article gets corrected.
- Standards Australia. Australian Standards (AS 3660 termite management, AS 4349.3 timber pest inspection)
- Queensland Building and Construction Commission. Protect against termites: termite management systems and inspections
- Department of Health, Victoria. Pest control: termites